Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi Nordic developers,
For my internship I’m developing a BLE application on de NINA-B111 module which does have the nRF52832. I'm using SDK 15.0.0 and Softdevice 132 v6...
We're disabling pending FPU exceptions and clearing pending FPU IRQs before calling sd_app_evt_wait(), as per a few references:
https://infocenter.nordicsemi.com/index.jsp...
Dear NordicSemi engineer:
I want to connect to a peripheral device using a modified ble_app_uart_c.The information of the peripheral device is below:
How can I connect...
I need to allow BLE connections for a period of time after restart, then prevent connections (unless a button is pressed). Is this functionality as simple as re-configuring...
Hello,
I am currently developing software that scanning ble advertisement packets without pairing and advertise them like beacon. I used examples which are ble_app_hrs_c...
Hi!
I'm working on HID mouse example on SDK 13.0.0, SoftDevice S1332 v4.0.5. I'm supposed to use this as a low power media button control, using a nRF52 DK. I've done a...
Hello,
We wish to use nRF52832 IC in our design. We will design an equipment which can connect to another device via BLE and can send some measurement data. Our equipment...
Hey everyone,
I'm working with nRF52810 . I want to write into UCIRs before program execution starts.
I tried to configure NVMC(Non Volatile Memory Controller) and then...
I am using the nrf905 in a project. The datasheet suggests crystals of 4mhz, 8mhz, 12mhz, 16mhz and 20mhz are all acceptable. Does the choice of crystal oscillator frequency...
Hi there, I have an 70mm wide and 50mm high PCB with an free space of about 32x26mm on the right top corner. At the moment this area is free of any traces and polygons. The...
In previous questions I inquired about setting the MTU size beyond 27 and thank to the answers I, indeed, manage to compile and run my program with larger MTU size definitions...
Hi, I have an issue with the watchdog and sd_app_evt_wait() when running the softdevice. It seems impossible to not let the watchdog go off while having an idle ble connection...
Hi there,
We're looking to improve the touch performance of our products by moving from PCB electrodes to a dedicated touch film. Can anyone provide any references to info...
Hello Nordic team,
What is the Maximum sampling frequency for i2s we can configure to nRf51 or nRF52 DK?
And if we enable UART module to print live of i2s on serial console...
Hi
I following the steps listed in the document Thingy Mesh Demo v0.1
https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
When i perform the step 5 "Open the...
