toochain：3.0.2 sdk3.0.2 nrf connect Every time I build, it gets stuck here: Found assembler: C:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi...
Hello, I know it's a bit basic, but running through all the docs for thingy91:x I got a bit lost.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/device_guides...
Hello, I am the hardware researcher currently evaluating this product.
I am currently working with the nRF54L15 DK and have encountered an issue where my application appears...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
Man,do you have the experience on DIY Bluetooth headset with PCA100059?
I raise this question for I hate the current product limit: limited time to run,short lifetime of...
Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hi,
I am implementing the whitelisting feature so that the NRF52 only pairs with one phone at a time. We require the NRF52 to advertise for 10 mins but I could only set...
IN looking at CONN_SUP_TIMEOUT below:
It says the units are 10 ms. if you take 4000 * 10 ms, you end up with 40000 ms which = 40 seconds - not 4 seconds.
Also for...
Hi,
As title, I'm the new for this.
I have one 52840 board and several 52832 boards, and one of them(sink) collect some data from other boards by using proprietary radio...
Hello,
We use nRF52832 with SDK-11 as peripheral in our project. We want to utilize white-list feature to limit the connection establishment. I have studied H ID Mouse example...
Hello, I'm trying to view the STATUS register of the timer (1 for example) but it is not display on the segger registers view ... Is it a well known problem ? Cheers, Sylvain...
I am developing application on nRF52832 with SDK14. I came across mem_section_dummy_rom and mem_section_dummy_ram sections in the linker script in the example codes. I couldn...
Hi
I have been using nRF52 in my project. I am not using provided uart drivers for one uart -> UARTE1. I am using DMA access and I have no problem to send and record messages...
Hello,
Can the nRFgo tool be used to compile/construct Gatt profile & service tables for nRF8240 devices.
If not is there a tool for construction the services (e.g. like...
Dear Sir,
Please tell me how to configure the NFC pine P0.09 & P0.10 as GPIOs. I followed all the procedure given in the development kli manual & on the nordic blogs also...
Dear Sir,
I am using nrf52832 & sdk 14. When I dump your twi sensor code(SDK14\nRF5_SDK_14.2.0_17b948a\examples\peripheral\twi_scanner\pca10040\blank\arm5_no_packs) in the...
Hi ,
Need a bit of help here.
I am trying to use TWI and SPI in a single code for communicating with two different slave devices, the LTC2941 coulomb counter and the EM4325...
I've adapted the SPI example to read a value from an Analog Devices ADXL350 accelerometer as follows:
But when connected to the accelerometer this hangs waiting for the...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
