I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
I want to turn peripheral device from application mode to bootloader mode from a central device(not app), so I am trying to write value 0x01 to dfu service.
Following...
Hi,
I am trying to evaluate the NRF51822 with S110 softdevice stack. My IDE is the IAR Workbench 7.10.1 for ARM. I downloaded the most recent s110 version (s110_nrf51822_6...
In the product specification page 165, I see than the continuos mode is 2 to 16kbps. In the page 167 this mode is 2 to 16ksps.
Which unit is correct, kbps or ksps?
If...
Recently I have put some code of my application into RAM. When I do not enable read back protection mechanism everything works, however when I want to enable protecting my...
Hi all,
I have updated a custom automotive PCB and am now using the nRF51824 instead of the nRF52832 I had been using previously.
Unfortunately, I have been unable to...
I am very excited about the Bluetooth 5 LR PHY, but do you plan to release an update to the nRF5 SDK to support the newest soft device S140 v5.0.0-3.alpha?
Hello
I am new to work on nrf52,
Please can someone help me regarding how to use hardware and software pwm together. I have a need of using 13 leds , so i need 13 pwm...
Please can anyone help me on how to use(program) PWM hardware with individual loading mode? My goal is to control 12 LEDs individually with different duty cycles and playbacks...
I want measure the current of a device over a resistor. It is connected to 5V which is over VDD(3V) of nRF52 Chip.
5V--->10ohm--->Device
the differential voltage of this...
Hi,
I am using SDK v8.0.0 , Softdevice s110 and Example is ble_app_uart(peripheral).
i want to reduce a range of nRF51822 beacon(PCA20006) up to 2-3meter..
i try this...
Hi all,
Basically I am doing an exercise on the BLE system use case. Let's say I want to setup a BLE system where there are the long range BLE capabilities in Relays and...
What is a minimal length of preamble, such that nRF51 is able to safely receive a packet with? Can it be made (via some magic registers) to be as small as 4 bits? Then it...
Hello!
I'm pretty new to BLE and Nordic, and hope that someone can give me some good advice.
I'm working on a project were I have 2-4 sensors, each connected to a nRF52832...
