Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
But in button event handler.
i want data to read from eeprom through i2c bus. and send it
through bluetooth stack for every press of buuton 0.
but in master control...
Hi,
Is it possible to start a Timer in an other Timeouht Handler?
Or Do i have to use something other to do that?
i use app_timer and Softdeive on the 51822.
best...
Hi,
i need to add a logfile System to my application so i thogut i could use the nrfUart example is this possible ? I looked in the code of Master Emulator nrfUart in C#...
Hi 'Nordic' guys,
splitting the original S110 hex file provided by Nordic , version 5.2, there is an error extracting uicr section.
Now is only 20 bytes and not 32 as...
Hi,
Is it possible to wakeup nrf51822 without using the GPIO peripheral's (i.e configuring a gpio button as a sense enabled)?
how to do soft reset?
Actually my requirement...
Hi,
i need to make pulse with one of my Timers. Timer0 is used by the softdevice, and Timer2 is used to make PWM. I need to make a Pulse wich is 100us long, every 250ms...
Hi,
What is the procedure and source code required to enable Device Firmware Update over BLE and USB. We are using nRF51822 chipset. Assume that our requirement will be...
Hello,
I am using a nRF51822 DK.
Actually I want to develpoe a product what can connect 3~10 slave(Low Battery device) by BLE.
And they have to reconnect fastly anytime...
A friend installed on two XP machines this software in this order..
Keil's mdk472.exe
Nordic's nrfgo_sdk_2.3.0_setup.exe
Nordic's nrfgostudio_installer_1_14_1...
I downloaded the nRF51SDK and followed the Quick Start guide in the Evaluation Kit Userguide (KEIL, Segger, etc)
But when I install nRF51 SDK v4.3, the installation failed...
Hi,
does anyone know if there is a document in which is explained, by Nordic, how to obtain a bluetooth certification using nRF51822 and S110 Stack ?
I know if a reference...
I have uploaded the following code, but I can not re-program the next.
#define AREF0 0
#define AIN3 2
#define AIN4 3
int main(void)
{
// Start 16 MHz crystal...
I'm looking best settings of fast connection to Android4.3
The time of advertise start to connection established average is about 7s
I think it is too slowly, may be My...
Hi
I write an application code to read and write the data from EEPROM, by using twi_hw_master.c.
its working fine. i able to read the data from eeprom what i have written...