nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Nordic Team,
We are using Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v3.0 to sniff packets from BLE 4.0 device - but we are finding it hard to connect...
Hello ,
i use blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. I want to flash the led with periods (period of 30 ms turn on 10 ms off) ...
Hi,
I'm using 52810 basing on ble_app_uart example. We use a IO to start or stop advertising. Start advertising w hen the IO level is low while stop advertising w hen the...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I am considering using two nRF52832 or nRF51822 's for a project which requires two way BLE communication. Pressing a button on one end should cause an event on the other...
Hello, I have an adafruit bluefruit feather m0 which has nRF51822 on it, I was able to establish a connection and send data until yesterday. When I try to find my adafruit...
Hi All,
I have a general question about the FreeRTOS implementation for SDK 14.0.0.
I've added FreeRTOS onto a basic UART BLE peripheral example that I wrote. I referenced...
Hey Guys,
I'm trying to import an existing Keil project into Segger Embedded, SDK 12.3.0.
I know this link exists which explains importing prior to SDK 14.2.0. However...
In the PS v1.4 pages 13-15 related to the QFN package.
Pins 11, 12 (P0.09, P0.10) are marked with the note '1'.
On page 15, at the bottom, the notes are enumerated:
...
I have a button that will put my device into pairing mode. While in this mode, I want central devices that connect to form bonds so that when not in pairing mode I have a...
Here I document how, in Eclipse, to start two, concurrent debugging sessions to two NRF5DK boards (or other debugging probes) , connected to different USB ports of the same...
Hello everybody,
I have problems with selectivity when I scan. There are 5 peripheral devices with different " DEVICE_NAME " but the same UUID and type (same " ble_uuid_t...
