Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hi! Im using a nRF51-dongle and the SDK v12.1. There are no exampels for Segger Embedded Studio but in Segger Embedded Studio im trying to use the "Import IAR EWARM/KEIL MDK...
Hi everyone!
Im using Segger embedded studio and its works well to import the keil project to SES. I dont get any errors when building or debugging but i cant se it in the...
I read that in large networks that configuring the relay nodes helps achieve low-latency communication. With the nRF Mesh, is it possible to automatically switch off the relay...
Hello,
I wanna use FDS module and started with FDS example given in SDK 11.
I have used the exactly same functions for initialization but it seems like FDS module is not...
The S120 Central after scanning, connecting, and issues a sd_ble_gap_encrypt() to secure the link. If the peripheral's bond (LTK) is corrupted or incorrect, the sniffer shows...
This: http://www2.keil.com/mdk5/editions/lite/
I guess the principal limitation is the 32K code size, but the full list is here: http://www.keil.com/demo/limits.asp
...
I have Stlink v2 programmer and I would like to use it to flash hex file into my nrf52832 I read a lot of threads about using tools like openocd but none was helpful, I think...
I'm attempting to build the ble_app_hids_keyboard example from sdk 14 using gcc and the compiler is throwing the error "No such file or directory", but the file is there and...
I have problem on SoftDevice V6.0.0(nrf52832) scan_start/stop. modified ble_app_blinky_c(ble_central) 1. app_timer add (20ms cyclic) 2. app_timer handler, run sd_ble_gap_scan_start...
Hi
The 'ble_app_multiperipheral_pca10056_s140' example for the nRF52840 has an 'LED' characteristic under which there is a "Nordic LED Button Service"
The value...
Hi,
I've defined:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 120 (in sdk_config.h)
I get "Insufficient RAM allocated for the SoftDevice" in nrf_sdh_ble_enable
nrf_sdh_ble_enable...
Hi everyone, I'm looking to buy nRF52840 SoC for my thesis but I'm surprised that none are yet available from Farnell, Mouser or Digikey ... I found few chips on Symmetry...
Dear Engineer,
We are working on 52840 usb dfu,program softdevice s140_6.0,
and usb secure bootloader,
evaluate board is pca10056,v0.9.0
Led1,led3 turn on once load...
I am very new to ARM controllers. All of my experience is with Atmel family, which I've been using for years.
I just got the nRF52 Development board and have loaded several...
Why do the version numbers have to be as follows for a merged hex file to be able to exit the dfu mode when flashed externally as a combined hex file (SD +BL + BL settings...
