I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Sorry I must have missed some crucial bit of documentation.
I have some code working using GPIOTE, however the inputs of the hardware, that will connected cannot be driven...
Hello,
I have interfaced MPU accelerometer on i2c and GPS on UART. Have enabled UART and using printf to display both sensor data. To begin with, both work fine individually...
Hi,
I checked erratas for nRF52840 rev1 and #164 is gone but #191 is still there. Can I have both #164 and #191 active in my code and it won't cause problems on either engineering...
Hello,
I have a question regarding the nrf uart driver. The RXTO event is never triggered even though the Interrupt itself is enabled (and the line is idle after a packet...
hi,
In Light switch Example ahead of time he have 3 Servers so we set SERVER_COUNT=3
if I want to develop Mesh Network..Where I introduce new Node, Provision the node...
when i use other hex file, it appear every time.
after i click "yes"， i can't scan the divece?
so what the proble ? how can i use "nRF Connect " with other hex file ,...
Hi everyone.
I want to use the nRF8001 in a low power application and therefore I want to save as much energy as possible.
I read in other discussions that the nRFgo studio...
Hello,
We are mocking our code but we are having difficulties eliminating the dependency of other files the mocked file includes due to the mocked header including the...
Good morning,
I am running the UART example from SDK 14.2 (example/ble_peripheral/ble_app_uart) on a brand-new NRF52832 development kit (PCA10040).
On the master side...
Hello.
I try to periodically updated data in my characteristic that way:
As soon as I connected via "nRF Connect", function " sd_ble_gatts_hvx" returns: NRF_ERROR_SVC_HANDLER_MISSING...
Hi all ,
I have SHT31 and I can read Temperature and Humidity value by NRF52 . But I want to create 1 service for display it on smart phone with the RH (name: Humidity,...
Hello,
I would like to measure the voltage of circuit GND by using the embeded SAADC of nRF52832.
But unfortunately I have no vacancy of GPIO to connect GND.
Could you...
I have set up a nrf52840 kit to upload data to nrf cloud via bluetooth but the data on the cloud is displayed as a hexadecimal number(1,2,3,4,5,6,7,8,9,A,B......) I want to...
I am not seeing a transition to BLE_ADV_EVT_SLOW. The transition I see goes from FAST to idle, without a transition to slow, from the configuration I don't expect to be in...
