I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello!
During the development phase, we have been flashing our nRF52 devices directly (though the debugger) and with no signing keys. We have also tested flashing the...
I would like to use the COMP capabilities.
The input is from NRF_SAADC_INPUT_AIN1.
The input voltage is 0.1-0.8V.
I would like to get interrupt every time we change...
Hello everyone,
I use sdk14.2 softdevice S132. I want to write "uint8_t some_array [7] = {0x00,0x01,0x02,0x03,0x04,0x05,0x06};" with use fds_write and read the array from...
When using BLE_GATTS_VLOC_USER to store multi-word characteristic values that are updated by application code, what is the recommended way to prevent a partially updated value...
I am working with ble_app_uart code, in that I am trying to send continuous data over BLE. But the BLE getting disconnected while sending large data.
So I planned to have...
Hi,
We are using nrf51822 QFAAH00 with SDK 110 v8.1.0 in our project, the application will hangs or not work when control stuck at address 0x6b0 (sometimes at 0x640) programmer...
Hi all.
I've followed as much information i can find regarding RTT. I understand that it was build in to the SDK after 11 or so and I followed the guides on https://infocenter...
I use the connection event extension, but there are several concepts that I am not very clear.
Software:S132 v5.0 . SDK14.1.0 nRF52810
Goal: I need to use high throughput...
my TWI device sensor, both its writing and reading address is 0x55. This seems weird for library of nRF since the last bit should be set as 0 for transmission and 1 for receiving...
hi Engineers!
the questions - is it possible to implement multi advertising (need two) broadcasters with different advertising data use SD 140-6 (nRF52840) ?
in the new...
Our Project is based on the multiprotocol THREAD BLE dynamic example.
We have the BLE DFU also as part of our project and it is working.
We now need to add the flash storage...
Hello :)
I have a question about the timing of sending a bluetooth write request. I am using two nrf52 developement kits, one as master and one as slave. From my master...
I am porting to SDK15 and this is the error I am getting:
../../../main.c: In function 'ble_stack_init': ../../../main.c:2746:2: error: unknown type name 'nrf_clock_lf_cfg_t...
Hi,
While customising code for my application, I noticed that in on_connect method of ble_nus.c, in the p_client we set is_notification_enabled = true after checking ble_srv_is_notification_enabled...
