I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
We are looking for a BLE-enabled chip which can bind to a smartphone, with the aim of performing proximity tests. to make sure the person in possession of the chip is indeed...
We want to design a small tracker for key rings like car keys etc, it will be linked with mobile app. Is it possible to do so?
Whatever I have read till now is it is possible...
Hi,
We are planning to run the nRF52840 in CKAA configuration 3 (attached) in Normal Mode. When we boot, our regulator will provide VDD = VDDH = 1.8V. Reading through the...
Our product is using NRF24L01+ and PA to transmitter data. It pass all the test of FCC PART C but the BAND Edge measurement.
The below 2 pictures is NRF24L01+ Band edge...
Hello everyone,
I have been dealing with this issue for some time now, and I think it's time to find a definitive solution, I am sure there is one!
For my projects,...
I had some questions when using nRF5SDK160098a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble for OTA test. Who can help me answer my question?
1. Can I return the...
Hi,
i have created some custom characteristics and i am enabling read and write characteristics in that, but when i am trying to write or read some data it seems that it...
Hi everyone,
I am trying to connect my nRF 9160 DK and Thingy:91 to TIM (Telecom Italia Mobile) CAT-NB1 network provider from Brazil. I am using the Asset Tracker and...
Hello,
For my project I want to use broadcast packages to send data to multiple devices at the same time.
I've seen that there is a beacon application that "should"...
Hi,
I'm trying to develop a custom service and am following a few examples in trying to do so. The software crashes for me everytime after advertising the new service...
I am building a custom device that incorporates the nRF9160. For testing I would like the device to work in China. I believe NB-IoT is the only network that is supported by...
Hello,
I have multiple records that I want to update during the runtime of the program.
What is working:
1. I can write in memory for the first time initial values...
Hi ,
I am using nrf connect 1.2.0 dk. I am now testing the https client example.
However, I always get the connection fail error as belows.
Provisioning certificate...
Hi:
I want to send pictures and voice.So it needs to be faster.What should I do?
I use nrf52832/sdk16.If nrf52840 is used, can it reach 2Mpbs?
Measurement example:nRF5_SDK_16...
