I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
What is the purpose/functionality of SWO pin (pin 6) on the Debug In port?
I see it connected to P0.18 on PCA10040 and P1.00 on PCA10056, but I’m developing custom board...
Hi,
Though I could able to successfully provision light and switch using nrfMesh Android application with all elements being configured and also could publish/subscribe...
Hi,
Recently, I am studying the blog as the link below:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/bluetooth-prepairing
We would like...
Hi all,
On the iOS version of the Blinky APP, there is a statement
Created by Mostafa Berg on 01/12/2017. Copyright 2017 Nordic Semiconductor ASA. All rights reserved...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
Hello Developers,
I have just started playing around with BLE Mesh Zephyr examples on my recently purchased nRF52840-PDK board.
Anyways, I am bit stuck with one fundamental...
Hi,
I've used the nRF51822 in the past to make sensors that connect to a mobile device. Basically it worked just like every other non-mesh BLE device:
1. It advertised...
Hi:
I'm developing a project with nRF 58232 in ble_app_hrs_rscs_relay example ( s132 sdk:nRF5SDK160098a08e2 ). The device need to be central and peripheral,My device worked...
Hi there,
I'm planning and hoping to use the nRF52840 (in module form) for an upcoming medical device design.
This will need to interface to a PC/Mac/Linux to send specific...
