We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I'm experiencing a freeze - at least from user's perspective - when using a slightly modified "usbd_cdc_acm"-example and applying some human generated load (meaning: hitting...
I'm using two nRF52840 dev kits, both running with the same code.
I start the timer and every 20 ms, when the timer expires, I set a new 20ms timer, and in handler(),...
Hello, guys.
I can rewrite s_dfu_settings that are in bootloader.
I try to update firmware from application that means that I save firmware in second bank and I need to...
Folks,
Been struggling for a couple of days with a comms issue that I assumed were at the other end of my system, but am starting to think it's at the nRF52 UART end and...
nrfutil
dfu serial -pkg ble_ app _v1 .zip
-p /dev/ttyUSB 0 - b 57600 - fc 1
When activating DFU sometimes on the last packet sent to the bootloader, I see "Read no data...
I need to know how to set up the SES debugger to continue debugging when the program jumps from application into the bootloader.
nRF52832 SDK v15.3
Using the following...
C:/Program Files/SEGGER/SEGGER Embedded Studio for ARM 4.18/gcc/arm-none-eabi/bin/ld: Output/Debug/Obj/port_cmsis_systick.o: in function `RTC1_IRQHandler':
1> .....\nRF5_SDK_for_Thread_and_Zigbee_v3...
Hi,
When I use SDK16, for example, the ble_app_hrs, the Keil will throw a error about the system_nrf52840.c.
1. For Device Family Pack version 8.27.1, it could not find...
Hello
I am contacting you because I have 2 problems:
1. I downloaded the "nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b" available at this address: www.nordicsemi.com...
Hi!
I'm using nrf52832, SDK 16 and s132. I've successfully used a ble_app_hids_keyboard example to make a Bluetooth HID peripheral device to transfer sensor data to the...
I want to use a timer to generate an event at a rate of 16kHz. So just as a test I'm setting up TIMER4 and a CC event to toggle a gpio pin. As I understand the clock source...
Hello everyone,
I set up Thread Secure OTA DFU Example by using a nrf52840 DK as DFU server and a nrf52840 Dongle as DFU client. I am using nRF5 SDK for Thread and Zigbee...
I'd be grateful for some assistance with what I may be doing wrong.
I have programmed the serial example on a device and the server example on another device.
Copied the...
Hi everyone:
I was testing the bonding with passkey entry, but it seems failed.
The slave 51822 EVK board is set with "BLE_GAP_IO_CAPS_DISPLAY_ONLY" and "MITM = 1".
...
Hello devzone! I am using translation.
I am using a DK board (PCA10056) to examine the current consumption of nRF52840. I commented out the advertising_start() of the SDK...
