Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello ,
I want to read the values from tera term , and PCA10040 have to read that value on polling basis .
Then advertise that values / data as manufacturing data. i am...
Hi
it looks like my MQTT-SN is not working.
I am trying to run MQTTSN Example in nRF52840 devices. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi,
I have 3 Devices that constantly broadcast their position to each other so the other can adjust the position each other. they act like master and slave but ther are...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
Dear Nordic
my SOFT DFU fail when I init the WDT, but I have feeddog and disable the WDT, like below:
static bool app_shutdown_handler(nrf_pwr_mgmt_evt_t event) { switch...
When access_model_subscription_list_dealloc() is called the entry is memset to 0 and the ACCESS_INTERNAL_STATE_INVALIDATED flag is set.
The function access_model_subscription_list_alloc...
Hi all,
I have a nRF52 DK (PCA10040 V1.2.1), and I want to learn how to develop on macOS.
I read from this link , and I got following information.
But I cannot know...
Hi,
I use The Texas Instrument software "SmartRF Packet Sniffer Bluetooth Low Energy" to catch the communication between my peripheral build with nRF52832 and Zwift (software...
Hello
I am trying to configure your TWIS (not using the SDK) and have run into the problem that the TWI master cannot pull the SDA and SCL line low. So, the communication...
52832's PDM function. After initialization, call the nrf_pdm_enable function, and then call the nrfx_pdm_start function. NRFX_PDM_ENABLED is set to 1. But the clock pin always...
I am evaluating the NRF52810 (using the PCA10040 dev kit), and I am having a hard time getting down to the described power consumption of the chips. I am using the power profiler...
i have done ble_app_template writing values from nrf app connect, in that i have send only integer values from nrf app connect
now i want to write float values from nrf...
Hello,
I have enabled the watchdog timer in nrf52810 with below code
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Pause << WDT_CONFIG_SLEEP_Pos...
Hi,
I have some problem with experimental_lpn project from sdk_for_mesh. (Today I tried both sdk 3.2 and 4.0)
Code loads and starts ok on my PCA10040.
After first steps...
