after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello, I'm trying to set up SPI communication with a sensor from my nrf5284_pca10056 running zephyr.
This is my prj.conf file:
This is my .overlay file:
And this...
I'm looking at the GPIO functions in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/peripherals/gpio.html , and looking at the function prototype...
Hi
I'm have and NRF52840 with a MPU9250 connected via TWI. The connection to the MPU9250 is successful, I can find its address on the bus (0x68).
I've implemented a very...
I am trying to add to an existing project gpiote
I have copied the code from the example project and tried to add all the files and changes to my sdk_config.h to match the...
Hello all,
I'm trying to develop a basic bike computer, compatible with ANT+. For that, I'm using nRF52 DK. My main objective is to be able to connect to any commercial...
Hello,
I have nRF52840 with code that is based on SDK16.
I am not using Softdevice in my project - just MBR , Bootloader and Application.
I was able to upgrade my code...
Hi all,
We are successfully using the nRF52840 chip in one of our projects except for the DFU functionality. We tried following these tutorials without success:
devzone...
Hi, I'm dealing with the ble long_range_demo. Central packet gives arrival time and rssi signal through the rtt viewer. However, I am willing to know the sending time of the...
Hi all,
I am investigating Mesh SDK and interoperability between devices.
We have bought some Hytronik devices which are qualified with Bluetooth.
Strange thing is that...
Hi,
I am new to thread network. In my application only a few nodes, mostly one. How can I connect this one node to the internet? Assume WiFi is available.Can I use the thread...
Hi,
Good Day!
Statement of Problem: In our application, we are using a 3S2P Li-Ion battery(12.65V). BMS is built using BQ24XXX TI's Li_ion controllers (Which does not...
Hello,
For the past couple weeks I have been trying to get Gazell working concurrently with BLE using the timeslot api. Everything appears to be working correctly - all...
Hi,
In one of your posts , a few monthes ago, you wrote that LTE BLE gatway for thingy is "work on progress".
Quote: "We haven't made this demo for the Thingy:91 yet...
