Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I've been experimenting with the Mesh SDK (v3.2) on nRF52832 boards. After doing some end-to-end latency experiments, I've come up with some questions associated with...
51822, S130, SDK11.0. In order to save current, I disabled fast adv and set the slow adv interval to 10seconds. The current is low now, but I am facing connecting issues with...
with regards to nrfconnect ios v2.2, has anything changed with respect to service changed characteristic or service and characteristic discovery?
(behaviors described seen...
Hi nRF team,
I am configuring my GPIO pin with below code sample.
out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrfx_gpiote_out_init(MEM_SPI_SS_PIN, &out_config...
in ¨¨Blinky example¨¨ we press button on one board and led get ON on other board.
I want to ask how can I modify this example or any other example
what are the functions...
Hi
I am looking for BME680 example code for Thingy91,since I donot have access to NB-IoT / LTE network as of now, i can't use the asset tracking demo code. I just need BME680...
hello
we used sdk_15.2.0 ->proprietary_rf -> esb_ptx example to check 52840 transmission.
now we have 61440 bytes need to be sent out. i used following code；
int main...
I`m searching after a document / description how to setup a user test case for BLE RF distance range measurements. Maybe Nordic have a smart phone app which we can use to...
I am evaluating NRF for a commercial project. I am also new to this BLE business so trying to learn fast.
I am trying to run the supplied BLE UART example on the NRF52DK...
I am trying to develop a low power scanner with nrf52832 which is is acting as both central and peripheral (beacon)
I need to detect other tags like itself transmitting...
Hi,
is there any example of firmware that can be used on nRF24LU1P that perform some data receiving on RF side and send them over USB?
The most important part is the USB...
Hello, We have designed a PLE peripheral based on nRF52840, SDK16.0, Softdevice v7.0.1. We have having an issue where, occasionally, we send a certain data (a command) to...
Hi everyone,
I created a custom service that I want to be advertised through scan response. Also, I want to advertise the INFORMATION SERVICE through advertising data. I...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
