Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
Hi .
I am using nRF52840 dk in windows 10 environment.
I want to measure the RF output power of a single nRF52840 using nRF52840 dk.
I succeeded in generating a...
Hello,
On my custom board, on nrf52832, I can can use app_buttons for all usual pins, but not the XL1 (P0.00). I didn't try XL2 (not routed)
Using this pin as input or...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
I have the NRF_CCM peripheral setup to encrypt packets on-the-fly. I can verify packets are properly encrypted when the payload size is 27 bytes or smaller. However, anything...
Hi,
I have created a configuration based on usbd_app_uart example where both usbd and softdevice are enabled on my device as soon as the device is turned on. When I transmit...
Hi,
I am developing a simple application that utilizes a light switch client example for NRF52832 with SDK15.0 and Mesh 4.0.
I am facing a problem when using the FDS module...
What could be the reasons that cause DFU Bootloader BLE not working with nRF Connect on PC (while it works with nRF Connect on iOS)? I have had various problem with nRF Connect...
Hello
I am using Seggar Embedded Studio for ARM V3.4 and nRF_SDK 12.3.0. I am trying to understand interrupts and interrupt handlers.
The interrupt request for Watchdog...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I have nRf52840 and I am trying to add a timer to examples\ble_peripheral\ble_app_uart...
Hi,
Setup:
I’m sending ble packages with around 80 Hz from an server (nrf52832 sdk 15.2) to a client device ( nrf52840 sdk 15.2)
One Ble package consist of several...
This is probably a simple question for an experienced nRF developer.
I have a demo going where I can read or write any of four characteristics I have set up on my peripheral...
Hi all, i have two units of a custom board project that i made.
In the first board, I plugged the pins in the right position as you can see in the figure below, a). nRFgo...
Hello everyone,
How to read Scan Response in contentiously in every 5 seconds in my ble_app_uart_c. i can advertise ibeacon and Scan Response data both in same code but...
