The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
We have been using RSSI as a signal for doing location services, however we are find that a bit challenging. From reading the literature in the field, several researchers...
Dear community,
for my upcomming project I would like to use the nRF52832. Since there also exists a development kit I started to make myself familiar with Embedded Studio...
I have two nrf52 chips connected to each other via SPI
I send data from my Nordic Uart app to my nrf52 chip 1 and I want to send the data that I receive from Mobile app...
Hi,
I'm trying to prepare the firmware for a nRF24LU1+ in order to allow automatic driver installation on Windows.
Based on Microsoft documentation during device enumeration...
I like to provision a node in mesh with the help of computer. Shall i use serial example? Is it possible to use without interactive_pyaci to provision a node with computer...
Hi,
My questions is related to this one: https://devzone.nordicsemi.com/f/nordic-q-a/58250/short-range .
We are also developing board and range is shorter than in smartphones...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
I encountered an issue, please kindly refer to the attachment for the detail.
"'' The problem is: a> Run demo on PCA10056 (BLE adv & ANT continuous scan). b> ANT Dongle...
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
