Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
I am running S140 on an nRF52840 custom board. While doing some power profiling, I noticed a spike of current of ~15mA when going from sleep mode to waking-up due...
I've created read onle characteristic called "log". In main.c i try to update it by calling : ulogd_characteristic_update(&m_ulog_service,Log_Data_arr)
But nothing happens...
How can delete individual peer bonding data without to affect the rest bonds:
-currently connected (after disconnect)
- some peer by providing RPA (assuming RPA matches...
Hi,
Is it possible to enable the transmission of 2 bytes of preamble and use the TIFS register to force a delay to transmission when in proprietary 2Mbps mode?
Thanks...
Hello, I'm using SDK 16.0, softdevice s132 v7.0.1, I'm sending the device to SystemOFF and configuring a pin to wake it up with
nrf_gpio_cfg_sense_set( IMU_INT2_PIN , NRF_GPIO_PIN_SENSE_HIGH...
Hi,
I am using a 52832 part as a peripheral communicating with a central running on an ESP32. It operates in the following manner:
1. When it is active, the peripheral...
I am getting a "Stopped by vector catch". This isn't particularly informative. How does one find the code location where the fault is generated?
Thanks
Hello everyone,
I just started learning BLE. I want to develop an application that gets RSSI from a beacon and displays the magnitude of RSSI using 4 built-in LEDs.
Beacon...
We want realize mesh network to mibile phone clients using BLE5
We assume we are have to use 3 types of devices:
1) Mobile phone/pad with built-in BLE5
2) Access points...
In our use case we are using the nRF9160 in eDRX mode with an eDRX interval of 40.96sec.
I'm noticing that the power required to transmit a message varies widely between...
Hello, I am pretending to catch BLE packages with nrf52840 dk with Visual Studio Code or Clion, which one is the best for this kind of programm? Thanks
Hello,
I'm looking for some documentation, and maybe a complete list of possible data I can read over MQTT from a Nrf Thingy 91. Specifically, we're using these fields right...
Hi all,
I have read about the local binding between the endpoints (same device) and i wanted to implement this type of binding in a device which has 2 endpoints (switch...
Hello,
I am using the nrf9160 DK board ver 0.9.0 running the latest version of the asset tracker application. I am wanting to switch the serial ports off to measure the...
This discussion got mixed up with a discussion about what Nordic means by a 'system attribute' (which is still not clear). In any case, in that discussion I was trying to...
