Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hello,
I´m trying to update the certificate of my nRF9160-DK. To do this the modem has to be in offline state. I´m running the AT Client sample like it is shown in the chapter...
I am curious if there is an inherit maximum transmit duty cycle of either M1 or the nRF9160. I am asking for this because we need these numbers for SAR test. Our product will...
Hi All,
I am working on a project with NRF52840 , we are looking for a solution to do the OTA to device by the central device , both of them are using NRF52840 as BLE module...
Hi, I need to be able to count the number of packet Tx and Rx from one board to another in order to compute a packet loss ratio for certification purpose. To achieve this...
hi all:
Use PPI+timer+adc, in the following ways:
called stop, then unable to start adc, Couldn't get into the NRF_DRV_SAADC_EVT_DONE.
Could you tell me how?
Hi,
My product is undergoing susceptibility test and strange issue is happening after the test for 1-2 hours, ie while trying to send data with higher MTU size notification...
Hi!
I have an issue with log-entrys disappearing seemingly at random. Not super frequent and possibly (but not confirmed) more often towards the beginning of a freshly started...
Has anyone been able to successfully setup a Segger Embedded Studio project to step through the Bootloader included in the nRF5 SDK for Mesh ( https://infocenter.nordicsemi...
Hello to everyone and thanks in advance.
First of all, im new at this and would i might be asking something stupid.
I have a development, that one of the features would...
I see in NRF5 SDK ShockBurst compatible mode and relevant support.
I dont see such thing in Bluetooth core5 specification. So - ShockBurst is you proprietary creature ?...
I see the messy information elsewhere especially in selling infos about antennas for BLE5. OK optimal antenna is a quarter length of average wavelength -( 299 792 458 ) /...
I ordered nrf52-dk.
I am trying to install the SDK using nrf Connect Desktop using the option below:
Getting Started Assistant Guide to set up the nRF Connect SDK
I...
At least the combination ARM gcc 9.2.0 and nRF5 SDK 16.0.0 prevents me from doing incremental builds after some source file have changed.
The problem is with wrong dependency...
Hello,
I am developing an IEEE802.15.4 Beacon with the nRF52840-DK, SDK 16 and the nRF-IEEE-802.15.4-radio-driver . My problem is that the consumes ~400uA of current in...
