This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I'm using nrf52840 DK to connect and receive usbhid message with the message size > 64 bytes (examples 343 bytes), so the message is divided to multi packages. I modified...
I am trying to build the nrf9160 from segger studio. I have installed and expoerted path of zypher and gnuarm toolchain gcc-arm-none-eabi-8-2019-q3-update-linux
I am getting...
I'm trying to run SDK examples on BL652 module from Laird (which is basically nRF52832) by means of debugger from nRF52 Dev Kit
Strange thing is that all examples (even...
However, I don’t know which SDK we currently use:
“ The new device version is software compatible with the current version if using SDK14.2/15.0/15.2 and Softdevices...
Dear Nordic Community We are about to develop a module for the nRF5340. Unfortunately we are using EAGLE CAD and not Altium Desinger. Would you mind adding the nRF5340 reference...
Hi,
In our app we would like the USB to change role. For example depending on Scenario and Command over BLE we would like to change the USB Device class or even turn it...
I am having a strange issue while using pc-ble-driver-py to perform tests with a BLE peripheral:
In these tests, the Peripheral sends a lot of data as fast as possible using...
Hi
I am using nRF9160 DK board ,below is my code, I want to create two threads in main() function for LED 1 and LED 2 to turn on led alternatively.
For some reason threads...
Hello,
I am currently developing a small Star network for the nRF52840 dongle using plain 802.15.4 protcol with the IEEE802.15.4 Library provided by the nRF5 SDK.
I use...
I can compile and run the beacon example in long range mode but advertising packets are not being received by any app on my mobile phone. Is there an app that's written for...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Hello,
I want to put my nRF to sleep mode if I dont receive anything on UART/no activity on NUS for more than 10 mins.
Is there any example to achieve that?
Thanks...
Hello All,
We are working on a medical device that requires BLE connectivity. We could either use the nRF52 series SOC to run the application and the BLE communications...
I am using TWI 0 to communicate with an external EEPROM. 99% of the time this is going succesfully. For reasons best known to itself, my eeprom will sometimes fail to acknowledge...
