I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hello,
I am currently developing a small Star network for the nRF52840 dongle using plain 802.15.4 protcol with the IEEE802.15.4 Library provided by the nRF5 SDK.
I use...
I can compile and run the beacon example in long range mode but advertising packets are not being received by any app on my mobile phone. Is there an app that's written for...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Hello,
I want to put my nRF to sleep mode if I dont receive anything on UART/no activity on NUS for more than 10 mins.
Is there any example to achieve that?
Thanks...
Hello All,
We are working on a medical device that requires BLE connectivity. We could either use the nRF52 series SOC to run the application and the BLE communications...
I am using TWI 0 to communicate with an external EEPROM. 99% of the time this is going succesfully. For reasons best known to itself, my eeprom will sometimes fail to acknowledge...
Hi everyone,
I have an nRF52840 DK. So far, I have been programming the nRF DK using the UBS connector J2 and everything worked great.
Since yesterday, by following the...
I want to update status in manufacturer specific data of advertisement packet. is there necessary to stop advertising first then reinitialize advertisement data and again...
Hello peeps,
nRF52480 I2C Interface with Invensense ICM 20948. I am using SDK 15.2. I see there is some Support for MPU 6050 Invensense but not for ICM 20948. A lot of Registers...
Hello,
I am currently working on the nRF SDK for Mesh v3.1 and I am using a static provisioner as in the light switch example. I have merged the client and server functionality...
Hello! I have a custom board with a NRF52832 chip that is working fine with the last program I flashed into. But since yesterday I can’t access it to load a new code (flash...
What all do I need to modify in the Blinky peripheral (from SDK 16) with in order for the 840 DK to advertise and connect with CODED PHY in long range mode?
My code compiles...
Hi everyone,
I am looking at using MQTT v3.1.1 with TLS 1.2, to send data to Azure IoT Hub.
I tested the MQTT Simple sample and it worked perfeclty. So I am modifying...
