I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
To the kind attention of Nordic support team,
reading this https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059 thread,
I...
Hi, I'm using the Cyclone FX programmer to program our custom boards with the NRF52840 chip, but after programming all the hex files, the application starts straightaway bypassing...
I want to use a timer to generate a Manchester data. The fastest data rate is 3.906 K-bit. So I want to generate a timer interrupt once 128 uS. Can anyone guide me how to...
Hi,
I am using Laird's BL654 USB dongle based on the nrf52840 and would like to convert the peripheral USBD BLE UART example ( https://infocenter.nordicsemi.com/index.jsp...
Good day!
52840 datasheet states " If the power failure warning is enabled and the supply voltage is below the threshold, the power-fail comparator will prevent the NVMC...
After the MTU size exchange of 247 bytes with Android LL_LENGTH_REQ/LL_LENGTH_RSP are exchanged with 123 byte octets for TX and RX. Data flows properly after that.
But with...
Hello,
I'm working on NRF52840 drivers for custom hardware using Nordic's FatFS / SDIO drivers and a tickless FreeRTOS configuration. When I load the demo code (fatfs demo...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving "LTE link could not be established." and then rebooting.
Things I have tried...
Hi All,
I'm working on adding simple melodies (2-5 tones) to my app using the I2S module and i'm facing some problems:
How do i determine the tone?
Can i determine the...
The supl domain name doesn't resolve.... SPM: NS image at 0xc000
SPM: NS MSP at 0x20027508
SPM: NS reset vector at 0xe965
SPM: prepare to jump to Non-Secure...
To the kind attention of Nordic support team,
Let's please consider this scenario:
PCA10040 with ble secured bootloader already installed
PCA10056 with usb bootloader...
I'm confused by this because I believe I am writing to the correct LED Characteristic. The code looks like:
...
if characteristic. properties . contains (. write ) { ...
Hi
I would like to use an ENUM and STUCT within my application to maintain device state (IDLE, RUNNING etc). This state needs to update a BLE Characteristic. I have the...
Hi
I'm currently testing a microphone, I only want ADC reading from it to show how loud the sound is, so kinds like volume.
If I only using simple ADC to read the number...
