Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
I've got a custom board fitted with an nRF52832. Am running NCS v2.6.0. Operation involves:
1. Being in System On idle with all peripherals disabled to keep current to a...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Hello:
i'v try v2.0.2 and v3.0.0 and v3.0.2. got error as follow:
or
sometime install toolchain got msg " Failed to fetch available toolchains. "
what the url...
Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
In IAR Embedded Workbench for ARM, version 7.40.3.8938 (w/ common components version 7.2.4.3784 ) with nRF5x MDK for IAR version 8.0.3 .
When selecting the target in General...
Hi,
I have a couple of nRF Beacons and want to change the program so that it scans for iBeacon packets before starting to advertise.
The flashed program is just advertising...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
hi everyone.
we are migrating to nordic nrf51 series (before we used ble modules from another vendor blugiga which depends on cc2541 chip) so I m pretty new at nordic nrf51...
Hi all,
I'm using the pca10031 which contains the nRF51422 chip; as a packet sniffer to sniff the communication between my S5 samsung and my pca10028, but I struggle while...
Hi, I'm trying to use the example bootloader with the new NRF52, everything seems to work fine except that I'm unable to bond to the device when the bootloader is installed...
I sniffer the packets when I use a phone to connect to a BLE device.
However, in the packet with CONNECT_REQ label, the source address (init address) is not the bluetooth...
Hi.
I'm trying to communicate with legacy nRF24L01P using nrf51822.
I received packet from nrf24l01p, but I can't send information back.
The data I should send is more...
I use the persistent storage manager for saving some calibration parameters. It seems to work ok - I can power off/on, and the values are still there.
However, after I...
Hi. I would like to get into bare metal programming, and have decided to go for ARM processors. Are there any ns-kits or courses availible for purchase?
thnx in advance...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
