Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm experimenting with the relay as well as hrs and rscs demos. Basically, I want to check at startup for IRKs stored in flash on startup in the peripherals. I'm only working...
I have developed my custom board and my custom application based on nRF51822 and S110-v8.
It perfectly works with Master Control Panel v9.0: connection, bonding, dfu,......
Hi,
I am interested in your nRF51 IoT SDK, IoT SDK for applications using IPv6 over Bluetooth Smart.
The presentation www.youtube.com/watch describes an architecture...
I'm developing an application supporting concurrent central and peripheral connections and using the new Connection State module in SDK 10 to decide whether a BLE stack event...
Are there any modules/devices with sar certification for the nrf51?
I have a need for something that will be placed with an elastic band against the arm or upper torso...
Hello,
I am using S110 8.0 stack and 9.0 SDK and I am testing the signal strength.
Now I am able to get the BLE_GAP_EVT_RSSI_CHANGED event after I started performing rssi...
Hello,
I am investigating the on_ble_ev function and trying to get back the Connection Interval parameters set by the Master Control throught the ble_evt_t struture . Is...
Hi,
I want to use the NRF51-DK to program an external device. It worked fine so far using the J-Link Firmware. I had to switch to mbed since it is a huge mess to get it...
Dear all,
I use nrf51422 with S210 soft device. I need to read an attached sensor via TWI. The sensor returns 32 bits of data. I need to read that 100 times a second.
...
I try to build a basic ble advertising program, I'm using SDK9 and softdevice 110 hex coming with. but just by calling any ble instruction the system freeze(my led not longer...
As it was asked here and an answer was given, but it's not working.
@Vidar: I've taken dual_bank_ble_s110 bootloader example and removed all the call I don't need, left...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
hi
i have NRF51422-QFAA-R V2 ;
i want to know how connect reset pin of my jlink to it?
u see in pic that reset pin is on the swdio;
and also i want use a button to...
