Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hello,
I try to modify the advertising initialization to advertise only my custom service (BTS_UUID_SERVICE ). Objective is to hide (just during adv) others sig services...
Hi,
where could i find detailed current consumption and timings (wake-up, rx, tx, power down) in connected mode for RF51822, in order to compute average current value for...
My device :
nRF6310 Rev 1.4(nRF6700)
nRF2722 Rev 2.2
I will use those devices to test RF communication between nRF2722 and nRF51822. Software environment is...
Hello,
I am playing with the s110 ble_app_proximity example.
As I do not want to store info in flash, I do not want to use the bond manager, that stores data in flash...
I'm currently using a combination of the GNU ARM Eclipse plugin and the unofficial pure-gcc Makefiles to build my nRF51822 code. The build works fine with the pure-gcc Makefiles...
Hello everyone,
I want to create a real-time wireless sensor network. There are 8 sensors in the net. I use two nRF24LE1 as receivers to recieve the datas stimultaneously...
Any idea what the max SPI slave clock frequency is on the nRF51822? The product specification (page 46, v2.0) says the max SCK frequency is 2MHz, but I was wondering if any...
Hello together,
I am searching for the source code of the MasterControl Panel for Android.
Is there a reason, that the code is not available, because the source code of...
Hello,
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me.
www.nordicsemi.com/....
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
Hello
I am trying to build the nAN-36 application.
The main.c file include at least two files that I do not find:
#include "ble_eval_board_pins.h"
#include "ble_stack_handler...
