Hello,
we would like to test our product after production. So I would like to connect a PC to the unit via BT-LE. My Idea was to use the nRF52840-Dongle like the nRF Connect...
Hi,
When try to use timer based on nrfx ( https://github.com/NordicSemiconductor/nrfx/ ) directly on the nrf54l15 DK board, I found it never call the timer_handler( ). ...
Hello,
I am using nrf5340 audio BIS headset with other LE Audio Tx test. The nRF Connect SDK version is v2.2.0.
During the sync process on both sides, the headset error...
Hello,
I send you a message because I try to do work a sensor of type DHT11.
I am a beginner with Nordic SDK, I use VS Code to develop and NRF5340DK board.
I connect...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
I have made a PCB has 4 buttons and touchpad, now I want to drive all of them.
1. one button for left button of mouse. 2. one button for right button of mouse....
When I call the function sd_ble_gatts_sys_attr_set, the compile error "source\ble.c(142): error: #165: too few arguments in function call" showed in Keil V5. But I found just...
Hi,
I have used the following version for my development
SDK: 6
SD:s110_nrf51822_7.0.0_softdevice
nRF51822 :3.0
Recently we are using nRF51822 3.1 QFACA1 1442AB...
Hi,
I am trying to setup DFU on a PCA10001 board with the following specifications:
softdevice v8.0
bootloader: From SDK v8 examples (bootloader\pca10028\dual_bank_ble_s110...
I updated my MCP to the newest version and then the new MCP wanted to update the pca10000 with the newest firmware--> failed. Now i can't get my pca10000 to work again. i...
Hi,
i am trying to connect via bluetooth using the gatttool on a Raspberry Pi. On the Nordic device I am using the BLE Proximity Demo. Everythings work fine, but after 30...
Hello all,
I am trying to get a communication between the nRF8001 and the nRF51822 using the UART service. The nRF8001 is connected to an Arduino and is working fine. I...
I am trying to find out the issue with my nonvolatile driver. I currently try running
nrf_nvmc_page_erase((uint32_t)(page_address));
However, that doesn't seem to...
I've been testing Pre-Production samples running a firmware in which I catch any and all Error codes or Reason reasons and write them to the gpregret register to be read later...
Hi, I am using a modified version of RBC mesh.
When I connect with an external device to one node using BT I get connected but I can get randomly disconnected when data is...
So, I'm trying to work around the Ble Uart example, using the PCA10003 Board. The example uses one of the buttons as a "Wakeup" source, but during the bsp_init() call, the...
Hi Nordics,
I would like to run the app example “ble_app_hrs_s110_hci_pca10028 (nRF51 PCA10028)” on the 32 MHz crystal. Can anyone help to change the code to 32MHz base...
Hello,
I am currently use the new SDK 8.0 for the NRF51822 (S110 soft device). I noticed that on SDK 7.0 for the ble_gap_sec_params_t struct , there was a variable called...
