Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi,
I'm trying to start advertising in gpiote interrupt. I have modified ble_hrs_demo code. I'm suing nrf51-dk with SDK9 and S110. Here are my code snippets(they are not...
I am working on my app and I need to combine the data from the main adv data event with the one from the scan response; in my setup one contains the full name of the device...
Hello,
We are currently writing the spécifications of a new device with a Nordic nRF51822. We have some questions concerning ANCS :
1/ Do we need to add Apple co processor...
Hello,
I have a collegues Macbook here that constantly connects to my mesh. Has this behaviour changed with the newest version of OSX? Has anybody noticed? I am advertising...
Hello Forum,
I have purchased an nRF52 Preview Development Kit and has successfully tested the blinky and the Hart Rate Simulator.
The document "Product Brief" from Nordic...
Hi,
I am trying BLE multilink central example from SDK9 on PCA10028 board, but everytime device gets stuck at LEDS_CONFIGURE() in main.c.
Below is my setup:
Flash...
Is there any way to stream the BLE data from nrf52 preview development kit to a PC/MAC? I saw this app devzone.nordicsemi.com/.../ but it doesnt work with nrf52.
Can anyone...
just i want to connect PC by normal BLE dongle.
i am using window8.1. and my nrf51822 chip using
ble_app_uart... i can communicate with smart phone but
on my PC, just i...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,all. i use ble sniffer to capture data between my phone and device,that sniffer says:malformed packed and connect failure.What's wrong?
连接不上问题抓包01.png
Hi
I've noticed that the Generic Attribute Service in profile code developed with S110 is missing the READ property on the Service Changed characteristic. It has INDICATE...
Hi, I want to logg faults on my system so in the app_error_handler I want to store some data to flash. This location in flash is erased earlier when no error was present so...
Hi,
I would like to know the time it takes to send the three advertising messages in one advertising period (on channel 37,38,39). What is it? How do I measure it?
Can anyone post this file, or a link to it? I don't have Keil(using GCC with Eclipse) so I appear to be unable to intall the pack that contains this. I am trying to get the...
I want to use timer0 to get exact time delay (without soft device used).
Timer0 configuration is as
void timer0_initialization(void)
{
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
