Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Can anyone tell me about fstorage module and can I use this storage space to store password? Will it give me any extra level of security? If so how to implement and...
I use a nRF51 dongle for some tests and I want to map the UART interface of UART_example on the pins 15,16,17 and 18 of the Dongle.
I try to juste adapt this lines of code...
I want to know the architecture of transmitter of nRF51822. I have questions as follows.
Does the block diagram of nRF24L01 show it? (nRF51822 has on-air compatibility...
Hi !
I'm running the ble_app_hrs_freertos example from SDK11 on the nRF52 dev. kit.
I would like to toggle some GPIOs to monitor the CPU activity and the FreeRTOS context...
According to this advertising blog: "The advertiser can use a whitelist to limit the interaction to a number of scanner/central device. The whitelist contains an array of...
I'm developing a custom board with nRF52832. We developed a flexible circuit for NFC antenna, and tuned following the indications on this post on the Nordic blog. Actually...
Hi,
I'm a beginner. I downloaded nRF5 IoT SDK, and tried to run and debug the application "publisher" on nRF52 platform. And each time, I got a message "no source available...
This is what we get from JLinkExe:
Found SWD-DP with ID 0x2BA01477
Could not power-up debug power domain.
Can not connect to target.
This all happens when we use P19...
Hi, i use softdevice 9.0 and s110 8.0.
I want to make 38kHz pulse.
so i tried to use nrf_drv_timer and gpio.
if i try to make 200us, it worked not bad.
but when...
Hi, everyone.
I have read the nRF5 SDK --> GPIOTE part in the infocenter. However, I have not get anything useful.
I just want to recieve a interrupt from an external...
Hi all,
I have installed the 1.21.1.3 nrfgo stdio from nordic site.
in device manger nordic board is not detecting( both nrf51 and nrf52) only in my lap.
any setting...
Hi
I am working on customization of proximity device with nrf51822 and I need to lock it to first connected device (so after first pairing I have to make blocking connections...
I took the reference of your example and instructions hear -
devzone.nordicsemi.com/.../
The program runs but get struck at sending the I2c write command .
Do I need...
