Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
good time dear Engineers!
Please explain how to use correctly HANDLE RANGE in functions of discovering.
I use CENTRAL with up to 8 possible connections to PERIPH, so pls...
Folks,
Have a very puzzling problem (which means I must have done something really silly :-)
Built a prototype in which the nRF52 section is a clone of the one in the...
Hi,
My team has created a custom board with NRF 52 and were able to flash the blinky sample successfully. The LED connected to P.20 is glowing on the custom board after...
Hello! I need to start a sequence of 26 pulses after getting low level signal on gpiote pin.
I can do it in gpiote event handler but I need it most of the time so I want...
I've been developing an application using the NRF52 DK and everything has been going as planned. I then made my own PCB which would take these modules by Rigado. The BMD-300...
Hi,
I am creating an application based on ble_app_hrs_c (central role). I have a few questions on this.
o I do not understand whitelist_load(). It first gets a list...
Good morning Nordic team,
I was measuring the nRF52832 chip in DC/DC mode. Everything went just as expected.
Now I was looking at the current consumption when the radio...
Hi guys. I have a EVK_NINA_B1 board which is based on nrf52832 and SDK12. I am trying to run the ble_peripheral/ble_app_uart/ from examples. I can send message through "nrf...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
