SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Are there plans to release the files for download instead of online-only access through the Infocenter? It was always so nice to have them on-hand to grep in the previous...
When I try to compile DFU examples, I get the following errors :
"..\..\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production...
I have my custom board wired to the nRF52 DK. Using the SAADC example code located in GitHub I am trying to set up SAADC to measure the coin cell battery that will power the...
I am sending and receiving streams of data over BLE.
Do I need to add a checksum byte for every GATT write/notification/indication to ensure that my data is not corrupt...
Hello All,
I am interfacing nRF905 as a receiver mode which are interface with nRF51 DK.
As a transmitter used this module www.alibaba.com/.../RF-100m-transmission-distance...
Hi,
I'm facing a little problem with custom service characteristic. I've set char settings as follows
attr_char_value.init_len = sizeof(uint8_t);
attr_char_value.init_offs...
Although this is easily fixable, Nordic engineers should be made aware that they made a minor change in SDKV12 that breaks makefiles on the Mac.
In /components/toolchain...
Hi,
I have downloaded the latest SDK12 for nRF52.
And i tried out the new "BLE Secure DFU Bootloader" example.
But i found that doing the BLE DFU with nrfutil on...
Hi,
I have nrf52 DK and sdk11.
I want to implement the time using internal RTC , the clock should run if the power is off ,i'm implementing in central code ,it has to...
Hi, I'm planning to add bluetooth LE support to my Arduino based project. I want to use nrf52832, but I couldn't find any example on Arduino interaction with this radio. I...
Hello. I have the need to get a device's unique address that remains stable across device firmware upgrades, etc.
Before SDKV12 I've been using sd_ble_gap_address_get(...
Hi
I want to know how to use ppi to wake up CPU from IDLE mode.
I've tried to use timer timeout event for triggering Port Event and wake up CPU, but can't assign NRF_GPIOTE...
I have been using a module of nRF52832. I write the Direct test mode in the module, to measure the current consumption of the Tx and Rx. DTM setting is + 4dBm, DCDC off. As...
Hello,
I try to send about 80kB of data between 2 beacons and I have encountered some problem that I got no idea how to resolve.
I have managed to connect devices, discover...
