An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Do the GPIOs sink current even when there is no power applied to the nrf52 chip?
We connected a LED to one of the GPIOs and connected the other end of the LED to VCC. The...
hi all,
yesteryday,I download bootloader and app to my nrf52832 by nrfgo studio, but I checked the option lock entire chip from readback ,after that,I found I can not download...
Hello,
I am working with the newest revision of the nRF52 Development Kit and the app_beacon example.
I try to change the clock source for the following code:
nrf_clock_lf_cfg_t...
On SDK 11.0.0 only ( NOT the alpha release )
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort...
On SDK 10.0 only
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort to main the quality of the release...
I am testing nrf5 IoT tcp client example. (in \nrf5_iot\examples\iot\tcp\client)
DK side:
IP:2004::213:ddff:fe4c:6032
run as client.
2.6lowpan border router...
I'm using the ble_app_template of SDK11. but I dont have an external oscillator, so the run time freeze at ble_stack_init
in this answer , the solution is to relace NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I have a NRF52DK (Chip Label: PCA10040; V0.9.0; 2015.44; 682646724) and when i try to start the DK as described in the getting startet page, Step 5 failed as LED1 is...
Hi,
I am planning to make a program so that when a beacon goes far away a specific distance (around 5m) then the led should light up.
I have taken some measurements...
Hi,
I have a couple of eval boards that were created for software and hardware development. We have two versions of the nRF52832 on these development boards. I know that...
I am using nrf51822 powered by a 3.3V regulator in a li-ion powered application. We have a high current load that we're controlling with PWM at 20kHz. Radio performance is...
I want to bond with an peripheral, which has static passkey hardcoded in it. If I want to bond with it with MCP, I get an request for passkey, I can then bond and encrypt...
My environment for this is
Ubuntu 14.04
ecipse Mars2
ble_app_uart project of Nordic SDK11(makefile project)
armgcc
nRF52 PCA10040 Nordic board
ERROR...
I am trying to figure out how to exit a loop of my program using a button press on the nRF Toolbox UART app. Say it's button 4 for sake of giving it a value. I am using an...
Hello,
I've been trying to use nRF Connect 1.0.0 on OSX 10.11.6 with a nRF51822-powered board ( this one, to be precise ). Whilst nRF Connect finds the serial port and...
