Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
i have ble running perfect in nrf51422 until i turn timer 2 on and this is code for init timer2
void timer2_init(void)
{
NRF_TIMER2->MODE = TIMER_MODE_MODE_Timer;
...
I am running ble_uart_app in SDK_11 s130 on nRF51-dk
I am trying to detect certain pattern received in the UART Rx.
Here is my code.
void uart_event_handle(app_uart_evt_t...
I'm running SPI master (spi_master_tx_rx) at 4MHz for multi byte burst reads. As seen in the attached screenshot there are 5.5µs delays between the bytes. The delays increase...
hello there ,I am writing spi code for slave which has 19 bytes of data. my nrf51 is master.
now my slave has clock polarity =1, clock phase =1. i am uploading project...
Hi All,
I'm trying to test the ble_app_hrs_rscs_relay example on an nRF51822 (256 Ko flash / 16 Ko RAM) with the softdevice s130 but unfortunately the program is not being...
I am using ble_uart_app on SDK_11 nRF51-dk s130.
I would like to send binary hex data instead of ASCII. Looking at ble_nus_string_send(), it seems that sending binary hex...
Hi ,
Recently started working on nRF52832 and tried implementing its various applications for NFC, which includes URL, android application, name tags. Can anyone suggest...
As part of some testing, I downloaded some wrong files and seem to have contaminated the default boot files. So now when I try to download the NORDIC hex files, i get an error...
Hi ,
We are using NRF52, S132 softdevice ... Whenever we do hard reset everything works fine .. But if I do flash from my IDE (using eclipse,this is a soft reset) and it...
I have a hard time to initial a twi ,I reference the example in the SDK11.0，and I used the board is 10040,I copy the example twi sensor code in my project ,but there is an...
I'm getting the error code 0x4001 from sd_clock_hfclk_request and I can't find where the error codes are defined/explained for this function. Can someone point me in the right...
Hi,
With the following program running, how can I achieve the lowest power consumption between timer events:
nRF Timer is running with the HF crystal requested
...
51822, config a pin as output , in the param , set disconnect or connect the input pin, when config as output ,what mean disconnct/connect input pin?
I use a pin to light...
For my project to simulate the spreading of a disease I am thinking of recording the complete social network on the beacons and then collecting the data to a pc. I have roughly...
