When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to know how to control the timeout from when the program goes from Bootloader...
My set Up:
TI as Peripheral,
Android as Central,
Nordic as Central
I am doing directed advertisement using TI as peripheral.
Using Andriod as central, I am successfully...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board.Using the OTA Tester (s210), I am currently doing an OTA Update with the s210 dual bank...
Hi all,
I have an STM32 connected to an nrf51822 via uart, and I want to do a firmware update of the stm via ble.
Therefore, I would like to take advantage of the Master...
Hi
my idea is to open and close pipes identified by BLE address of device.
Currently I enable ESB on BLE disconnect using timeslot API.
How can I do this "on the fly...
I'm testing with Soft Device 8.0.0, ble dfu operation with single bank, nRF toolbox on Android version 1.13.1 (installed on 5/11/2015). I generated a zip distribution file...
Hi,
is there any way to connect at the same time multiple devices with Android/iOS nRF UART app to an nRF52832 with ble_app_uart example?
I was thinking about adding advertising...
HI all,
I am setting these parameter as follow in my ble_app_template sample.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) /**< Minimum acceptable connection...
Hello everyone
I'm the proud owner of a nRF52 Prev. DK and trying to get my project to work. I would like to sample 3 to 5 analog signals using the ADC on the DevKit, followed...
A beginner's question.
I am using UART over BLE to send data out.
As codes below, ble_nus_string_send() works and continuously sending data out, with the Wireshark's...
I have some problem when I implemented 52832 dfu.
I implement it with sdk 11.0 and a third party core-board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio...
Hello i have a system that which i get data from a ultrasonic sensor and send it to Arduino UNO and nrfConnect application via the RBL Shield ( nrf8001 ) so i want to do it...
