Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
Dear Nordic team,
I am currently working with the Thingy:91X (nRF9151) and nRF Connect SDK v2.9.0 , and I am attempting to run the official ECDSA sample from your documentation...
Hello everyone
I need help. I have a custom board that uses the nRF5340 microcontroller. I am using the Zephyr OS and nRF Connect SDK Toolchain v2.9.0. How do I update my...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Hello,
To finaly adjust the inside crystal capacitor at the end of production, I need measure the LFXO and HFXO frequencies signals to fine tuning. How should I do ?
Best...
Hello,
We have developed a custom board using the nRF9151, with the design and board files largely based on the Thingy91x. We are using the nRF Connect SDK v2.9.0. When...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
Hi!
I try to write SD to 52810 and nrg go studio can't do it. After recover it can't to switch normal window with possibility erase device and SD write. What possible reason...
SDK 14.2 / SD132 5.0 / NRF52832 --> NRF52832
There is a thread here which discusses "when NUS is ready" : https://devzone.nordicsemi.com/f/nordic-q-a/28208/when-is-nus-ready...
I'm using SDK nRF5_SDK_15.0.0_a53641a, and I was able to trigger the hard fault handler from within the Nordic NFC library. Nothing was running. The microcontroller was asleep...
Hi
Some time ago, we purchased a couple of boards, then (I believe) called nRF52 PDK. They are marked PCA10056.
We need to obtain more nodes. From gleaning information...
Hello there,
I'm looking for a good source that explains the ideology of the Nordic methods for programming and debbuging the nrf5 chips so I'm looking for something that...
Hi,
I'am trying to run the example in Software Development Kit > nRF5 SDK > nRF5 SDK v14.2.0 > Examples > Bluetooth low energy examples > Experimental: IoT Examples > TCP...
Hi,
We have our nrf52840 module going to be ready soon. For production testing, what is the recommended and capable lower tester and upper tester? I am sure that nrf51822...
Hi all I am wrking in an sample be program where ble is advertising everey 5 seconds. I have configured app timer with fire period = 5 seconds in order to read a sensor. After...
Hi,
Ipv6 UUID 0x1820 shall be present in the advertising process. Is it mandatory to put it in the ADV_IND message or can it be in the SCAN_RSP one ? ... the scanner, 6BR...
Currently, we are testing Bonding & Connect.
Please see the attached log below.
If Click 「Bond」 on Android App (nRF Connect), disconnection occurs after "PM_EVT_CONN_SEC_SUCCEEDED...
Hello,
I have the following question: when developing a software product, I developed my own service. It consists of one characteristic and several descriptors (valid range...
On our products, we assign a custom sequential mac address to each unit (we use this number in other places in our system). I believe this is an issue due to the bootloader...
Hello all,
We are using nRf52832 DK.
We are trying to run TCP Client example from IOT.we have even burned the s1xx_iot soft device.We are getting the the error "CMSIS...
Hi,everyone!
I need to configure an external interrupt so that when the interrupt is triggered, I can do something else
When I configure it in the following code...
