Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
After getting SDK 12.1 and the S332 v2.0.1 softdevice working, I started working on updating the bootloader from the S132 bootloader we've been using to supporting the S332...
I am trying to set up a humidity sensor over I2C and I'm trying to use the twi interface. There are examples where the app_twi interface is used. I am however unable to get...
I'm working with a development prototype board with the nRF52832. It is connected to a main processor in our design over UART. We are working towards being able to do the...
Hello Nordic team
I am working on nRF52840, SDKv-15.0.
Is there any example code available which can send message from central device to peripheral device apart from ble_app_usrt_c...
Hi,
I'm tring to enter DFU mode by combo keys by KEY_COMBO_TWO_KEY_REGISTER().
In v1.1, I used m_pwr_mgmt_shutdown(M_PWR_MGMT_SHUTDOWN_TYPE_DFU) to enter DFU mode directly...
I'm looking at decreasing the motion sensor update rates for the Thingy:52 to get less frequent readings into the sample app. I have seen in the MPU9250 specs that I don't...
Hello Nordic team
I am working on ble_uart_c central example on nRF52840 DK, SDK v-15.0.0. Example code working correctly I can exchange data between peripheral and central...
Hi I am trying to reduce the power consumption of the badge of my company as much as I can. We use a proprietary radio protocol on the nrf52832.
I'm currently developing...
I have SD and BL secure flashed to the device, and now trying to get the second part of buttonless_dfu + app with settings flashed next. After flashing the second part, DfuTarg...
I'm attempting to optimize our application for battery life on the nrf52832.
If I execute a floating point calculation to rescale RGB to PWM, I start drawing 6.2mA, eliminating...
Dear all,
We are programming the FICR and have found very little documentation on the random number generator fields: - TRNG90B.BYTES - TRNG90B.RCCUTOFF - TRNG90B.APCUTOFF...
Hi
I have followed this example: https://github.com/bjornspockeli/custom_ble_service_example through to the end, but am now having issues with some intermittent behaviour...
I need to transmit and receive beacons using nRF51 DK. I saw a few examples in the SDK ble_beacons where we use the app, but I need code to transmit and receive both using...
I am trying to send 'h' or the number 1 using vendor defined page (custom HID descriptor). How do I do it?
NOTE: I have worked with hid mouse & keyboard examples and also...
