Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
Hi,
I have a BLE application, which I want to interface with PC via serial communication through USB.
It seems that just adding Softdevice breaks the USB_CDC_ACM example...
Hi all,
As a followup of this question, I started with the Thingy Mesh Provisioning Demo v0.5. However, I cannot get this version working possibly due to some unclear points...
Hi,
Am developing a beacon using nrf52810. I have a doubt on how to program the nrf52810 which I made using the schematics and layouts given in the Nordic website for nrf52810...
I am noticing that FDS requires me to specify a "record size", but there is no maximum specified, so I am testing it. Currently my program attempts to store 32 words, but...
I want to add some code to static void app_onoff_server_set_cb(const app_onoff_server_t * p_server, bool onoff) in light switch server application.
My intention is when...
When nrf51422 passed the authentication, when entering the rx mode of DTM, there was always a -59dbm launch at the 2.79GHz frequency point, what caused it, and how to eliminate...
Hi, I am trying to interface MPU6050 IMU module with NRF52832 DK.
I need to send the Accelerometer and gyroscope data to mobile app by using BLE_UART program
this is my...
Hi,
I'm trying to send a broadcast message from my client to all my server. Actually i'm working over a modifed version of the light switch example.
i saw that in the...
Hi i am using nRF52832 with SDK v14.0.0 on LINUX, so usually a service and a characteristic have the same name space but you just change a few bytes for every id. But the...
Hi there,
I am having issues to run my program after a MTU increase size.
I am getting the following error:
I am not sure if it is related to the RAM size values...
How to select endpoint transfer type in hid keyboard example?
I am using nRF5 v15 with a nRF52832 and Soft Device s132 and the reports keep being sent as a bulk transfer...
I'm finding my PCA10056 nRF52840 Q1AAAA development kit to be acting very strangely.
1) I takes almost 3x as long to program as a PCA10040
2) Generally I have to program...
I'm using nRF24L01+ since some time, the version on board with LNA end PA with very good results. The electronic is shielded on that module.
Very rarely it happens that...
