Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
In NRF5 SDK17.1, I disabled the Bluetooth broadcast channels 38 and 39 by configuring channel_mask. However, when I measured the broadcast current waveform, I found that there...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi all,
lesson2, excercise2 is missing the code snippits.
Excercise1 and excercise3 do have code snippits to copy.
I tried on both Chrome as on Edge, but the snippits...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
On the nRF5350 I'm currently seeing about 30 kB throughput via bt_l2cap_chan_send. It seems that could be optimized to over 100 kB. I'm looking at some values in the l2cap...
I am using zephyr_nanopb_sources to add some protobuf files to my app target, and this works fine in a normal build without mcuboot. However, when building with mcuboot it...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
In the old Nordic SDK we had the option of using "high accuracy" interrupts with GPIOTE by using something like NRFX_GPIOTE_CONFIG_IN_SENSE_LOTOHI(true);
Is there a similar...
I'm currently working on a project using the nRF52833 with nRF5 SDK 17.1.0 and SoftDevice S140 v7.2.0 , aiming to run BLE (Peripheral role) and Qorvo DW3000-based UWB communication...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
I am trying to run some of the more basic examples included in the nRF Connect SDK on the nRF5340 included in a Thingy:91 X . I have installed the latest version of the nRF...
Hi all,
I've build a custom bord with an nRF9151, I try to connect to aws iot but it's seems it's doesn't work probably cause by bad cert, I got AWS_IOT_EVT_DISCONNECTED...
We have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-1 and the same Toolchain, IDE: VSCode + nRF Connect plugin
We need to control the GPIO LEDs from two cores ( P9.00...
