I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
I'm trying to use an ILI9341 display with nRF52840 in Zephyr (v4.1.99). The build fails with multiple errors about missing Devicetree properties when compiling display_ili9xxx...
Hey I was working on starting sample code of wifi in ncs v2.6.1. When I added the correct ssid but wrong password in the prj.conf to check the status of the connection failure...
Hi there,
I am currently trying to use device sleep modes with Matter. Nevertheless, once I add "CONFIG_PM_DEVICE_RUNTIME=y" to my prj.conf, the main-method is not longer...
Hi, I have been experimenting with the Direct Test Mode program. I am using an nRF9160 DK, specifically the bluetooth chip nRF52840.
The Direct Test Mode is not officially...
Hi,
I am using sensor observer sample to get the data from sensor sample. However, I notice the power consuption is too high. I have look thourgh the forum and found this...
Hello,
Recently, my team has been struggling with an issue regarding a nRF5340 device that's encapsulated and inaccessible to be flashed with a JTAG connection. Our normal...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello dear Nordic support staff,
I'm working on some legacy code (NCS 1.8.0 in case it's relevant) and see this in the inclusion list of one of the files:
Functions...
Hi,
I`m designing the schematic, and met some problems, could you please give me some guidance?
Does the pin only supports the described peripheral function and not...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
