Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
In our project nrf52 device scans for nrf52 beacon device throughout the day. It scans number of beacons available and send it to esp32 device on serial. that is how its working...
Hi, Everyone
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
The size of the file has increased dramatically when I run mergehex.
1. nrfutil settings...
Hello i'm currently working on the central part of the DFU i succeded to make it work and now i'm working on the link loss part.
I used This to make the DFU work but it...
Hi,
I am facing the same problem as in question ' USBD don't work with debugger ' from @ Dusautois Jérôme
I am trying the same code both on PCA10056 and my board. In PCA10056...
Hello! I am useing nRF52832 with custom-made board.
SD 5.0.0 and 14.0 SDK
I am using modificated example of "ble_app_template", i added simple custom service from example...
I'm using USB based DFU on Windows and on Linux 18.04 LTS VM on Windows.
Platform: nRF52840-Preview-DK
SDK version: 15.0.0 (nRF5_SDK_15.0.0_a53641a)
example USB Secure...
Hi everyone,
I was just going through the library functions provided here in this link : nordic functions twi
But inside all these functions ,there is this parameter...
platform : nrf 52832 SDK : 14.0.0
I used gpiote to detect sensor's interruption . there are two sensors ,so I configure the gpiote like this :
neither of the two sensors...
Hello, I want to ask if is possible connect nRF51 Dongle in Shield Host USB ( https://www.electrofun.pt/usb-host-shield-android-arduino ) with arduino .
Thanks very much...
Hi!
My design has to be tested at 50V/m according to MIL-461F. Are there any experience with this high field strength or the MIL-standard? I want to avoid the cost of shield...
We are currently going through certification and have had an interesting failure during radiated emissions. When in normal transceiver mode, all is well, but when we put the...
Hi all,
I am using NRF52832 QFAAB0 with SDK 14.1v . Am not configuring any peripherals and just using the BLE stack in my application. During the power_manage() call the...
Hello,
I tried to port my projekt into SDK 15.0.0. During the compilation process I often get the warning:
Warning: The header file 'cmsis_iar.h' is obsolete and should...
I've read this tutorial: https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
And also Bluetooth CSS, Part A, 1.2,...
When using uart example on my curstom board, from /examples/peripheral/uart ,at baudrate 9600, bits are read with a little offset - so that starting from 4th bit, it is mistaken...
