Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I got a problem that doing the DFU through buttonless example, but successfully upgrade only in bootloader.
I used OPPO R9s (Android 6) with my personal cell phone...
which pin to use for TWI method communication, in board type 10040 nfr52832 model Taiyo Yuden EKSHJN
in file 10040 I have this definition of pins: what should i change...
Hello:
I have been at this problem for days now and not getting anywhere to a solution. My app is using a static passkey for encryption and does timeout after 30 seconds...
Hi,
I'm experimenting with incorporating " ATT_MTU Throughput" Example into our project.
I'm using nRF52832 as the peripheral and a SDK52 as the central.
The central...
Hi Everyone
I am trying to achieve the following objective
I want to upload the hex file of my application code which blinks leds after 1 second without using th SWD interface...
Hi,
I have my application working on NRF SDK11 on NRF52832 with softdevice 2.0. I am porting the application to SDK 14 and SD 5.0. I am facing APP_UART_COMMUNICATION_ERROR...
I posted the ble_app_uart example on the nrf51 dk board and tried searching for an app, but searching on Android, but not on iOS. Why? You have used nrf_toolbox in your app...
Dear all, my goal is to make a wireless HID device using nrf24/nrf5x products so, I've noticed the nRFReady Desktop solution that seems to implement the
RF connection nRF5x...
Hello,
I am trying to port the light switch server example form the nRFSDK for Mesh to IAR Embedded Workbench for ARM.
I am using
nrf SDK Version 15.0.0
SDK for Mesh...
Problem : bytes are lost during UART communication with the module, hardware flow control is enabled, at speed higher than 38400 baud/s, when softdevice enabled and test board...
Dear Nordic
I have facing some issues in RTC side. In my application RTC and BLE works same time . First installation and set time using function nrf_cal_set_time() works...
Hi all,
I want save and read flash in example light switch proxy server .
I add code part of provisioner example into proxy server example
This is my code ;
And...
Hi everybody,
I have a question about the nrf52832 how to set the tx power in the ble peripheral uart example. i want to set both the advertising tx power and the after...
Hi,
I'm testing BLE Central multilink base on nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_multilink_central\pca10040\s132\arm5_no_packs
With modification in main...
