after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am having interface nRF51 with RF receiver. Output of RF receiver connected with GPIO pin of nRF51.
How can I detect interrupt on gpio pin?
Thanks & Regards...
Hi,
I'm using Secure_Bootloader example of SDK 15.0.0 and I can't get the Logger module to work. I set NRF_LOG_ENABLED to 1, increased memory regions in make file, so the...
Can the esb bugfix timer (currently TIMER_3) be set to another un-used timer without any side effects? I need to implement the async uart from SDK15 and it uses TIMER_3 and...
Is there a simple example which supports LESC Just Works for peripheral mode only? The lesc_multirole example seems a bit too much since that also supports central role. I...
I am sampling 3 sensors using the ADC peripheral, clocking it once every 15us to sample the 3 sensors (3us acquisition time + 2us processing = 5us per channel).
I use the...
hi,
How can i set Destination Address to a particular Mesh Node. so that all message reach that particular Node Only.Since provisioner can set address while provisioning...
how to use app of mesh to send message to node ?
I already got the source code from web: https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library .
1\ i have add three...
I would like to put a nrf51822 device into system sleep (not off) mode and wake it up (not reset) with a GPIO transition from high to low. I used SDK(nRF5_SDK_12.2.0_f012efa...
Hello everybody, I tried to activate the PHY Coded in the UART Example from the SDK15.1.0 examples.
For this purpose, I have set NRF_BLE_SCAN_SCAN_PHY 4 in the sdk_config...
hello,we are developing NFC on NRF52832 recently,we want to use NFC as a label,T4T,but we have some problems as follows:
1、firstly,we want to develop NFCT by ourselves(not...
hello , i'am working actually on the timer of nRF52840 S140
my timer look like this:
but how to switch from millisecond resolution to microsecond resolution ? ( APP_TIMER_TICKS...
Hi!
I've try to made bootloader/recovery application that should to replace existing run-time application of the device. The F/W file for replacement placed in external...
Hello,
I am using Eclipse with ARM toolchain on ubuntu to buid my application with softdevice s132 api version 3.1.0. I managed to build on eclipse and merge softdevice...
We have a GPIO configured in the GPIOTE to generate an interrupt on the LotoHi and HitoLo transitions (Toggle). Inside the interrupt handler we would like to perform a slightly...
