Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
In [sdk10_folder]\components\ble\ble_db_discovery.h , BLE_DB_DISCOVERY_MAX_SRV is given the value 2 .
In [sdk10_folder]\components\ble\common\ble_gatt_db.h , BLE_GATT_DB_MAX_CHARS...
In another thread entitled:
Change in GPIO to start/stop timer and fire interrupt
The following code is used:
NRF_GPIOTE->CONFIG[0] = (GPIOTE_CONFIG_POLARITY_HiToLo...
Hello,
I'm trying a very simple thing; to light a LED on button press. I'm using SDK 9.0.0, nRF51 and SoftDevice 110. However, button handler is not firing.
So, APP_BUTTON_INIT...
I'm new to using nordic parts (nRF52832). We were previously using device manager/pstorage but recently transitioned to peer manager/fstorage.
However, we presently manage...
Hi, In my project I want to add added total 7 services but I add seven services it not advertising, If remove one service it advertising properly. I am using .nRF5_SDK_11...
Hello all,
This is my first post to the developer zone.
I'm creating a product using RFduino, which uses the nRF51822 chip for Bluetooth LE. (See www.rfduino.com/.....
I've recently been noticing on the Rev 3 silicon that there is a 19mA current rush at the Start of a connection event at the rising edge of Pre-processing.
What could this...
I'm encountering some problems with the nRF51 plugin v1.2 for BDS, none are show stoppers but I'm reporting them here so others are aware of them and maybe they'll get fixed...
Is it possible to integrate the master end of the OTA DFU process into an iOS or Android app?
The scenario would be that the iDevice or Android downloads a new version of...
Will the system automatically turn and keep HFINT ON when keeping only RTC ON?
In page 102 of nRF52832 Objective Product Specification, when the system enters ON mode,...
I have been searching around, and it seems BLE devices need to be paired through their app on phones, as opposed to discovering and pairing through the phones settings menu...
Hi, In my project I am using SDK11 (i.e.nRF5_SDK_11.0.0-2.alpha_bc3f6a0) and s130 soft device.
In my projects I am using 128 uuids for services. I got the problem is, while...
Hi
Im working on the project which relates to sending data through ble. I use nrf51822 Evaluation kit and the data is from uart. How do I send data greater than 20 bytes...
We are developing a product based on nRF52 with BLE communication.
We have PCA10036, with engineering sample 1, no more compatible with new soft devices.
Should...
Hi everyone,
I am struggling to get the GNU Debugger to work and break at breakpoints.
I followed the GCC and Eclipse tutorial: devzone.nordicsemi.com/.../
to install...
