Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I am interested in developing an nRF51822 application for an old PCA10001 nRF51 evaluation kit using a Mac OS X platform. I've downloaded and installed the following tools...
Hello,
I have a nRF51DK.
I am trying to use the TWI driver to communicate via I2C with an accelerometer MMA8452Q.
I already have a working code based on several SDK examples...
How much additional current does enabling the FPU add to the nRF52 processor? I reviewed the Product Spec. but I can't seem to find this listed anywhere.
Thanks
We successfully used the pofcon on a 51822 based design using S110 ver 7 to indicate a low batter condition to the user. However, we are moving to 52832 (currently QFAA-BA0...
I have a peripheral based on S110 that is connected to by a central running S120.
The connection is established, the S120 interrogates the service and enables notification...
Hello,
Thanks for reading this! I have an odd behavior on my nrf52832 where I am capable of uploading a new firmware via BLE DFU to the peripheral device if it is not bonded...
I'm running into something weird on SDK8.0 (I will be upgrading soon to SDK10, however it's a layered roll out so I can't update right now unless you tell me it's a bug in...
I was trying to view the scan response packet using the master control panel app I have on my android phone, but I can't seem to see where it is.
I want to update the scan...
I'm looking at an application where it would be beneficial to be able to read data from the bluetooth device as it passes. It would be easiest for me to do this by simply...
I am using the TWI module in master mode, with sdk 10. I purposely create an error situation, in which the TWI gets stuck and keeps returning NRF_ERROR_BUSY every time I try...
I've completed the Custom service tutorial, and I wanted to port the system to use the SDK10 with the pack installer. I've run into an issue though.
The code runs fine...
Are the GPIO pins in disconnected state during the startup until they are configured by the Firmware?
If not what is the state of the GPIO pins during startup?
Hello.
I have problems uploading with DFU OTA any application. For this case, I am using "dual_bank_ble_s310" example.
First of all, I put this memory's configuration...
Hi,
I am using nrf51822 CDAB version chip which has 128kb of flash memory, my code is built on ble_hrs
I am trying to save my app_trace logs i.e., redirecting my printf...
Hi,
I'm using pca10040 board. For my requirement i'm using FreeRTOS. While creating task we need to set stack size for each task.
For that i created only one task with...
