Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello,
I´m using nrf52832 with sdk 14.2.0 and softdevice s132.
I'm trying the example bootloader_secure_ble and compiles me correctly.
The problem is that when I debug...
In a documentation i read that i can transmit power at minimum of -40 dBm ?But i cannot achieve my target as my range has to be minimum of one meter?
So how do reduce the...
After getting SDK 12.1 and the S332 v2.0.1 softdevice working, I started working on updating the bootloader from the S132 bootloader we've been using to supporting the S332...
I am trying to set up a humidity sensor over I2C and I'm trying to use the twi interface. There are examples where the app_twi interface is used. I am however unable to get...
I'm working with a development prototype board with the nRF52832. It is connected to a main processor in our design over UART. We are working towards being able to do the...
Hello Nordic team
I am working on nRF52840, SDKv-15.0.
Is there any example code available which can send message from central device to peripheral device apart from ble_app_usrt_c...
Hi,
I'm tring to enter DFU mode by combo keys by KEY_COMBO_TWO_KEY_REGISTER().
In v1.1, I used m_pwr_mgmt_shutdown(M_PWR_MGMT_SHUTDOWN_TYPE_DFU) to enter DFU mode directly...
I'm looking at decreasing the motion sensor update rates for the Thingy:52 to get less frequent readings into the sample app. I have seen in the MPU9250 specs that I don't...
Hello Nordic team
I am working on ble_uart_c central example on nRF52840 DK, SDK v-15.0.0. Example code working correctly I can exchange data between peripheral and central...
Hi I am trying to reduce the power consumption of the badge of my company as much as I can. We use a proprietary radio protocol on the nrf52832.
I'm currently developing...
I have SD and BL secure flashed to the device, and now trying to get the second part of buttonless_dfu + app with settings flashed next. After flashing the second part, DfuTarg...
I'm attempting to optimize our application for battery life on the nrf52832.
If I execute a floating point calculation to rescale RGB to PWM, I start drawing 6.2mA, eliminating...
Dear all,
We are programming the FICR and have found very little documentation on the random number generator fields: - TRNG90B.BYTES - TRNG90B.RCCUTOFF - TRNG90B.APCUTOFF...
Hi
I have followed this example: https://github.com/bjornspockeli/custom_ble_service_example through to the end, but am now having issues with some intermittent behaviour...
