I have a project using BLE as a central on an nRF5340 to connect to several devices. For factory test I am being asked to implement something that can be used in the factory...
Hi, my code will return ATT error code: 0x0E cyclically
I have check some tickets and try to update my central device to
Hoever, it still cannot, the error is like...
Hi,
I have designed a custom board, and I cannot get coexistence interface to work reliably. I don't get any errors, but I'm not able to connect to my board with BLE. WiFi...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
Dear Nordic Engineering Team,
I am currently developing a wireless ECG acquisition system based on the ADS1298 analog front end (AFE), the nRF5340 SoC, and the nRF7002 Wi...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
I am new to Nordic Evaluation Kit.
I am working in Nordic nrf51822 (PCA10001) Evaluation board.
Following are my setup.
OS : Ubuntu 14.04 64 bit.
SDK : nRF5_SDK_11...
Hi all,
I need to know the RSSI Value (distance) between my nRF 51 DK and my connected device (iOS Device). I made these code changes:
switch (p_ble_evt->header.evt_id...
Hello!
I've been using RTT viewer to view some data in my nRF52832. Everything works fine but I am unable to clear the RTT viewer terminal screen.
As it is in the manual...
Hi,
I am trying to get the experimental NFC example "HR with pairing over NFC" to work.
I can read the tag correctly with an android phone : the NDEF message is correct...
Dear All：
My NRF24L01+ use Dynamic PayLoad,What register need configure NRF51822?
NRF24L01+ Configuration as follow:
SPI_RW_Reg(WRITE_REG + DYNPD, 0x01);//Enable...
Hi,
I've been using the ble_app_uart example as a template for our use case. It is a good starting point. We don't actually need UART functionality, and we've assigned...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
Hello.
How to write custom firmware updater, which:
Takes new firmware from other device on SPI or I2C bus.
Writes it to flash ("bank1" at 0x1B000, or...
Hi;
I'm studying on SPI communication at nRF51822 (not DK) but i could not find the pins for spi communication, i read at somewhere SPI is only used at DK(developer kits...
