Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
when I start ADC the current will be HIGH .even I UN-Initialization it .
what I have done like that below；
before I started it The current is 0.6ma
but when I start...
I'm trying to communicate with a device over UART, and I'd like to return the response to my commands back to the function the transmission came from.
For example, I want...
I want to develop nrf52840 with ble mesh topology.
However I need one node to transmit data received from all the nodes via uart to a gsm module
Can anyone please tell...
Hello Nordic experts,
I am trying to use app_usbd_ep_enable and app_usbd_ep_disable in order to enable/disable an endpoint. I need this to fake usb unplug/re-plug. Currently...
Hello. I am testing the sending and receiving of UART using nRF 52840-DK. If you change the UART pin settings as follows, you can receive but you can not send. It is confirmed...
Although I have already seen this discussion ( https://devzone.nordicsemi.com/f/nordic-q-a/35183/no-idea-how-to-get-manufacturer-specific-data-in-central-side-from-advertising...
Hello,
I have an nRF52840 chip ( Holyiot nRF52840 module ) and I want to program the chip using an nRF52840 DK. The Holyiot module is basically an nRF52840 mounted on a...
I am having trouble turning on bonds for DFU.
First of all, before I describe this pain, can I choose to avoid this battle by just allowing unbonded devices to DFU? e.g...
Hello!
I just bought the Beacon Kit and i was following the user guide v1.1 and I have some questions about how to use DFU. I have already downloaded nRF Toolbox app.
...
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing a program with keil.
I want to know how to write the value obtained from the sensor to the SD card. ...
I am using proximity profile in sdk15 with softdevice 6.0.0 . I added flash write, writing continuously some data to flash. But it working sometimes only.
Hello,
at the moment my application is accepting more than one device if its not connected to anything. But I want that the application only connects to one device and...
Hello, i am using NRF52840 board with SDK 15.2. I am trying to read data from an advertising packet and i was just wondering if anybody on here had a good parser i could potentially...
