I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Is there a BLE development board that supports extracting IQ data from raw MCPD ranging？ Does nrf5340dk support users to extract IQ data for the development of ranging algorithms...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
Could you please help me out on how to read my EMG sensor values and display it via the Nrf tool box. I have a redbear nano v2 and the digital output of the sensor is received...
Hello,
I'm having some issues with the MAXCNT limitation of 256bytes because I want to send larger packets and receive packets through the SPI Slave interface, which is...
I have an external board based on nRF51822 QFAC. I have a nRF52 preview DK. Will it be possible to detect my external board if connected via the preview DK. I tried and the...
Hello,
We've a Custom board based on nRF52832, it works fine in beacon mode using the Synth Clock (else it doesn't work):
// <o> CLOCK_CONFIG_LF_SRC - LF Clock Source...
When using the PPK to measure the current of our custom hardware the lowest range doesn't give logical results. (Either the PPK python GUI or nRF connect) When the nRF52 on...
Reference: nRF52840 DK Evaluation Board Schematics
The following inductors are lised in the schematic:
L1
3.9 nH
High frequency chip inductor ±5 %
0402 ...
I am working on windows xp command prompt and using nrfutil version 3.5.1
I want to do a Device Firmware Upgrade over BLE through my nRF52 DK board on a custom element....
Hi there,
SPIM3 running at max speed (32MHz) will be the fastest external interface (along with QSPI)
Because I would like to make to most of it, I wondered if you had...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hi,
Please help me on the nRF52840 UARTE RTS signal, through the doc: "nrf52840_ops_v0.5.pdf", we can know if we stop the UARTE RX by trigger the "NRF_UARTE_TASK_STOPRX...
Hi Sir,
I hope to add ble_nus and ble_nus_c into Central_and_Peripheral projects (ble_app_multirole_lesc and ble_app_hrs_rscs_relay), I use SDK 15.0.0 and nRF52832.
...
Hi,
When I developed with the board of nRF52840, I met up with an issue of UART. Sometimes, the UART will get a DRV_ERROR and crashed. Does anyone meet up with this issue...
Hi,
I am developing a central and peripheral device with secure LESC connections using SDK v11.
My peripheral device is an already developed product. I am simply adding...
