Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hi there!
I'm in the process of updating our codebase from 2.4.0 to 2.6.4. We are using the nRF52840. My plan is to do this step-wise, following the migration guides for...
I am currently in the process of filling out the 18031 RED Cybersecurity certification documentation. I am currently analyzing the security vulnerabilities list of NCS v1...
I’m working on a BLE setup where:
A Nordic nRF52840-DK runs as the Central (it scans for devices with a specific name, then initiates a connection).
A Raspberry...
Hi,
I'm currently working with the Thingy:91X and would like to measure the total current consumption of the entire board using the PPK2. I understand that the PCA64165...
I am currently working on a 3D game in Unity (made in C#) and I am asked to connect a Nordic Thingy:52 nRF6936 (based on the nRF52832 SoC) to Unity to control a part of the...
Hi,
I'm developing custom firmware on the appcore and netcore. The netcore runs BLE controller, as well another custom IPC service to communicate between the appcore and...
The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I was given an existing code with a possible bug in it relating to RAM retention and I'm trying to make sense of what I'm seeing. I am using NRF52832 with SDK 17...
Function: Now we have developed a function similar to usb file upgrade on the application side by ourselves (which requires operating bank1, writing the Settings page, involving...
Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi There
while extending the actual Sofware with more flash entries i discovered that the capability of provisioing devices decreases, and end up in a hardfault.
Is there...
Hello
In my board I am using an ic as a switch to control the routing of the TX and RX pins of the UART, due to the fact that the nRF9160 does not have more than 4 peripherals...
Hello, I am developing a project that involves authentication over NFC, and need to store a private key in TrustZone. I found the psa_crypto zephyr sample in the sdk, which...
