Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
Hello, I am working with a Seeed XIAO nRF52840.
I'm able to get an average of 500 uA in SYSTEM OFF mode. However, for this application, the current consumption during wake...
Hi guys, With v2.8.0 sdk, L4_e3 code ( academy.nordicsemi.com/.../) works with nrf52833dk. We have a custom board that we designed. Here, nrf52820 chip is used. I can compile...
Hi,
I have thingy:53 and I have damage to the sw2 pin and I am unable to enter the DFU. I lost two tiny pieces that go just above the one in the photo and not even...
Can some one describe how this is supposed to work:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/mpsl/timeslot/README.html
I would have expected to see...
Hi,
I wonder if anybody could help me? What is the best way to close down the nrf9161 so that it reconnects quickly after powering back up again?
I'm running Zephyr 2...
Dear Nordic Support Team,
In the datasheet of the nrf9160 (nRF9160_PS_v2.2.pdf) the VSS pin appears in the section 6.4.5.1 GPIO Electrical Specification, but I cannot find...
I am preparing to make our first firmware release on our custom board, which is equipped with the nRF9160 SICA B1 , modem fw version 1.3.4 . Our application is based on the...
I've been running into a lot of issues where a change in the configuration for the application results in an answer that basically states:
"You're supposed to add this configuration...
Hi all!
I'm wondering why the VS Code has option to create a new board for the nRF5340-QKAA only?
I have on hands the nRF5340-CLAA and nRF7002 chips which I'm going to...
