Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
Hi! I'm developing on nRF51 with SDK 11 and trying to extend our application with buttonless BLE DFU support. Due to limited flash memory, we could only use single bank ble...
The website is broken for me, and I see a sequence of orange pop-up messages saying "An error occurred. Please try again or contact your administrator."
When I use master control panel to scan ibeacn, I find "Complete Local Name" in below picture,
How to set the "Complete local name" ?
I heard someone says set in the...
Hello,
I've now been looking for a while but haven't yet found anything working to programmatically unwind the call stack when working with the nRF51 or nRF52.
Basically...
We are completing the design of a PCB and have a mounting/assembly issue with the NRF52840. We In looking at the mechanical spec on your datasheet w find that A row of 24...
hi
1.does nRF5-SDK-for-Mesh v 2 support friend feature of Bluetooth?
2.phone with ble 4 can current to ble 5 mesh network?
3.is there any example of two above?
thanks...
I have connecting problem.
My setting...
1. OS : win10 x64
emulator : J-link(EDU)
2. installed
1) nRF5x-Command-Line-Tools_9_7_3_Installer.exe
2) nrfgostudio_win...
Hello
The scanner causes the code to freeze when a debugger is not connected.
We are developing a system where one of our units is to run on the nRF52832. During development...
Hi ,
I testing the " nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c " sample code with nRF52832 . Found sometimes get the advertising...
We are using nRF52840 with the nrf5_SDK_for_Mesh_v1.0.0 in combination with s140_5.0.0-3.alpha I'm working with the nRF52840-Preview-DK board. Task: program a bootloader for...
Hi, developers !
We are going to make a USB dongle that configures RF HID using nrf52840.
So when I look at the datasheet for circuit configuration, it says "High voltage...
Hello, I want to transmit data using the nRF52840 card and a smartphone. I explain: I must transmit data from the nRF52840 card to a smartphone. What is the best program in...
Hi,
I am trying to add logs to the Eddystone example using SDK15, SD132, arm5_no_packs, PCA10040 and Keil. I added the corresponding libraries to the project, entries...
