hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi,
normally, I would set the CMAKE_BUILD_TYPE to `Debug` to enable Cs "assert" function (not define NDEBUG). Zephyr (and Nordic-Zephyr as well) has the `CONFIG_ASSERT`...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I am currently developing a project using the nRF51822 with SoftDevice S110 v8.0.3 in Keil uVision.
To properly manage RTE components and dependencies, I need to use the...
Hi,
As the title states, after a while, the nRF7002 fails to connect SSID after a while. It happens either we perform net_if_up/down or not. I suspect the nRF7002 to be...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
I'm trying to flash the hardware even with Programmer v4.6.0 but i get the following issue
18:59:55.179 Initialising the bundled nrfutil device 18:59:55.561 Using the...
Hi,
Update MDK to handle APPROTECT, MDK can be downloaded from MDK website, but no details on hot to update MDK to nRF5 SDK. Any guide lines to update the MDK with nRF5...
Hi there,
I'm using a slightly modified version of coap_client to test out network connectivity with a 1nce SIM card (USA). Essentially, I've modified it from a GET request...
Hi,
Im currently trying to add FOTA via BLE to my project.
To get familiar with this i wanted to add FOTA as described in the nrf connect intermediate course lesson...
